
Firm milk foam by hand? Does that work?
I am supposed to be able to make handmade milk foam in just ten seconds with the Bialetti Tuttocrema. I am skeptical, but I will give it a try.
Cappuccino, flat white, or Wiener Melange are simply a must for me. I love coffee! I usually froth the milk using the steam wand on my espresso machine. Until now. Because at my favorite café in Hamburg, I recently noticed the Tuttocrema from the traditional manufacturer Bialetti. You can use it to froth milk by hand – and supposedly, the fluff is supposed to have the same quality as with a steam wand. At least that's what the nice barista behind the counter said. A bit skeptical yet curious, I took the device home with me.
Simple system
At home, I quickly unpack it. The milk frother consists of an aluminum pot and a lid with a frothing plunger. Basically, it looks like a French press. Inside the box, there is also a short instruction manual.

The Bialetti Tuttocrema is available in a small, 166-milliliter version and a larger 330-milliliter variant. I chose the latter, which is supposed to yield up to six servings of foam.
The first attempt and what I learned from it
According to the instructions, I should fill the pot one-third full with milk and place it on the stove to heat the contents. Then, I am supposed to pump with the plunger for ten seconds to create fluffy foam.
I find it annoying that I have to rely on my own judgment when pouring. Unfortunately, there is no marking on the inside wall of the pot. Furthermore, the pot doesn't really fit on my ceramic cooktop. Its base is slightly smaller in diameter than the smallest burner. So, I am wasting energy while heating it.

I check the milk with a thermometer and take the Bialetti Tuttocrema off the stove at 65 degrees. A quick tip for those who don't have a thermometer: if light white steam starts to rise, the milk is at the right temperature for frothing.
Now, quickly off the stove and put on the frothing lid. It sits quite loosely on top. That makes sense to me, though, because air needs to flow in while pumping. I start pumping with gusto, but it's not that easy. I have to hold the vessel steady without burning my fingers while simultaneously making sure the lid doesn't slip too much. Otherwise, it makes quite a mess.
Speaking of slipping: next time, I will place the Tuttocrema on a silicone mat while frothing. It tends to wander across my smooth countertop while I'm pumping.
It's a shame that the pot is completely opaque and I can't see the progress. Nevertheless, I trust the manufacturer and curiously remove the lid after ten seconds.
I hesitate. Inside the pot is something "milk-foam-like." There are many large air bubbles, but the "foam" is still very runny. The inner walls are splattered from top to bottom, which doesn't look very appetizing. So, the result isn't exactly convincing, but the quality is sufficient for a Melange.
The breakthrough comes on the second attempt
Bialetti's timing is apparently too optimistic, and I was too frantic while pumping. This time, I heat the milk in a separate pot. That shouldn't have any impact on the result; I just don't want to waste energy.
The silicone mat was also a good idea, as it makes handling easier. I also change my pumping technique. To incorporate as much air as possible right at the beginning, I start with three full strokes. Afterward, I only lift the lever to the estimated fill level of the milk.
Actually, after a while, I feel a slight resistance. I let the strokes grow a bit larger. I only remove the lid now when I can barely push the lever down with one finger. I pumped for a good 90 seconds.

The result: a dream! Wonderfully fine-pored, slightly glossy foam that reaches almost to the rim. I get rid of the only larger air pocket by tapping it briefly on the countertop.

I use this to make myself a fine cappuccino. So the Bialetti Tuttocrema can do it after all! You just have to know how.
Why I will give the Bialetti Tuttocrema away anyway
I would recommend this product to anyone whose machine doesn't have a steam wand and who only wants to produce milk foam occasionally. Or for people who can't manage to get proper foam with a steam wand.

However, the Bialetti Tuttocrema won't be moving into my household permanently for two reasons.
First, there is the maintenance. By the second attempt in a row, the foam wasn't quite as nice anymore. I had only rinsed the non-stick pot with water, which is apparently not enough. Since the device is not dishwasher safe, I would have to wash it by hand after every use. That eventually becomes annoying.
Furthermore, the whole process takes too long for me. By the time I have heated and frothed the milk, I'm already sipping my coffee with my portafilter machine.
In a nutshell
Top-quality milk foam with a little manual effort
Pro
- produces milk foam with a good consistency
- frothing by hand is just fun
Contra
- missing fill level indicator
- no insight into the progress
- not dishwasher safe
Hamburg local, bookworm, and ice hockey fan. Dad and granddad. Constantly tinkering around with my smart home setup. I love DIY, the outdoors, fashion, and cosmetics.













