Best selling Outdoor lightings from EVN-Lichttechnik
On this page you’ll find a ranking of the best Outdoor lightings from EVN-Lichttechnik. To give you a quick overview, we’ve added the most important product details. This page always stays fresh and updates automatically.
1. EVN-Lichttechnik Solar LED path light
Solar pathway light with an integrated dusk and motion sensor for outdoor use. Since no electrical connection is required, the light can be installed almost anywhere outdoors. The charging time is 6-8 hours depending on the location. The light only turns on when the ambient light is below 20 Lux, with three different modes to choose from.
Mode On: 100% brightness for 6 hours (motion sensor inactive, light turns on whenever below 20 Lux).
Mode DIM: 20% brightness. When motion is detected, the light is at 100% brightness for 30 seconds and then returns to 20% brightness. After 4 hours, the light automatically turns off.
Mode AUTO: When motion is detected, the light turns on at 100% brightness for 30 seconds and automatically turns off when no further motion is detected.
A wall light is also available to match the pathway light. Battery type: 18650 3.7V 2600mAh. The included plastic ground spike has a length of 210 mm.
2. EVN-Lichttechnik LED recessed floor luminaire
The light fixture is made of aluminum, while the cover plate is made of V2A stainless steel. The cable entry is through the cable gland located at the bottom, which is suitable for cables up to 9 mm in diameter. To prevent condensation, there is a self-venting valve on the underside of the light. It is possible to install the light without the included plastic mounting pot; in this case, the hole cutout is 96 mm, while the installation depth remains unchanged. The included GU10 LED bulb can be replaced at any time if needed. The swivel angle is 10°. Additionally, a frosted protective glass is included.
3. EVN-Lichttechnik LED wall lamp
The LED wall light is made of aluminum using a die-casting process. Thanks to its given protection class, it can be used both indoors and outdoors. With its modern design, the light is perfect for all applications where special lighting effects are desired. The light head can be tilted 190° up and down. This allows not only to highlight building facades skillfully but also to perfectly illuminate stairwells and staircases, as well as much more. The color is similar to RAL7016.
4. EVN-Lichttechnik P-LED recessed floor light
The housing of the recessed floor light is made of solid aluminum, while the upper cover ring is made of V2A stainless steel, making it suitable for various outdoor applications. Installation is carried out using the plastic installation sleeve included in the delivery. Since the COB LED chip is permanently installed, there are no additional costs for light bulbs. Additionally, there are no extra costs for a ballast, as the connection is made directly to the 230V supply line. The maximum drive-over speed is 20 km/h. The light has a 0.50 m long connection cable with free wire ends. The beam angle is 60°.
5. EVN-Lichttechnik P6721502
The light fixture is made of solid aluminum, while the cover plate is made of V4A stainless steel. The included installation sleeve can be optionally used for mounting, with the installation depth remaining unchanged. To prevent accidental removal, the sleeve tapers towards the top, having a diameter of 58 mm at the bottom and 39 mm at the top. Since the LED chip is permanently installed, there are no additional costs for light sources. The maximum drive-over speed is 20 km/h. The type of dimming depends on the power supply used.
6. EVN-Lichttechnik LED EB light point
Small light point for a variety of applications indoors and outdoors. Due to the MM marking, it can even be used in furniture construction. Extremely low power consumption yet enough brightness to create visual accents, such as on the side panels of stairs, in terrace flooring, and much more. The light point is made entirely of stainless steel and comes with a 5 m long connection cable with free wire ends.
7. EVN-Lichttechnik Path light
EVN Lichttechnik Path Light WLL65081502
Manufacturer: EVN Lichttechnik
Name: Path Light 3000K, 230V, 625lm
Type: WLL65081502
Energy efficiency class of light source according to EU regulation 2019/2015: Not relevant
With light sensor: No
Type of luminaire: Other
With motion detector: No
With base plate: Yes
Bulb: LED not replaceable
With bulb: Yes
Material of housing: Aluminum
Surface protection: Powder-coated
Housing color: Anthracite
Material of cover: Plastic opal
Voltage type: AC
Rated voltage: 100-240 V
LED rated current at constant current: 350 mA
Control gear: LED control gear current controlled
With control gear: Yes
Protection class (IP): IP54
Impact resistance: IK08
Protection class: I
Max. system power: 8 W
Rated luminous flux according to IEC 62722-2-1: 625 lm
Light color: White
Color temperature: 3000 K
Color rendering index CRI: 80-89
Width: 40 mm
Height/Depth: 650 mm
Length: 120 mm
Diameter: 0 mm
Number of poles: 3
Conductor cross-section: 1 mm²
Connection type: Screw terminal
Massive path light made of die-cast aluminum and powder coated. The luminaire is perfect for lighting walkways, as edge lighting for flower beds, and much more. Thanks to the design, the luminaire does not create a glare effect. The lamp head has the following dimensions: LxWxH: 180 x 126 x 24 mm.
Supplied with: EVN Lichttechnik path light 3000K, 230V, 625lm WLL65081502, Packaging unit: 1 piece.
8. EVN-Lichttechnik LED path light
Massive pole light made of aluminum using die-casting and powder-coated. The light is perfect for illuminating walkways, as border lighting for flower beds, and much more. Thanks to its design, the light does not create a glare effect. The ring shape also allows for light to exit upwards. The color is similar to RAL7016. The light can also be operated via a central battery with an input voltage of 176-300 V/DC.
9. EVN-Lichttechnik Ground recessed luminaire
The light fixture is made of plastic, while the cover plate is made of V2A stainless steel. The cable entry is through the cable gland located at the bottom, which is suitable for cables up to 9 mm in diameter. The second cable gland included in the delivery can be optionally attached to the fixture, allowing for easy through-wiring. It is possible to install the fixture without the included plastic mounting pot; in this case, the installation depth is 180 mm and the required hole cutout is 137 mm. The high-voltage socket allows for various light sources up to a maximum of 35 W to be used in the fixture. The maximum drive-over speed is 20 km/h, and the swivel angle is 30°.
10. EVN-Lichttechnik ALU spot
The light can be mounted either directly on the surface using the attached bracket or optionally with the included ground spike in soft ground. The spotlight features a 1.5 m long connection cable with a protective contact plug. The cable entry into the light is made through a cable gland. The light can be equipped with a variety of light sources. With the mounting bracket, the light has a length of 155 mm in the non-tilted position, while the included ground spike has a length of 165 mm, and the tilt angle is 110°.
Product order
See all products